🌎
Nicholson Labs
  • About
  • Bioplastic
    • Tools and Materials
    • Tips and Tricks
    • Recipes (Refined Seaweed)
      • Carrageenan Ca01 (Solid, without Plasticizer)
      • Agar Ag01 (Solid, with Plasticizer)
      • Agar Ag02 (Film, with Plasticizer)
      • Agar Ag03 (Solid, with Plasticizer)
      • Agar Ag04 (Film, with Plasticizer)
      • Agar Ag05 (Solid, with Plasticizer)
      • Agar Ag06 (Solid, with Plasticizer)
      • Agar Ag07 (Foam, with Plasticizer)
      • Agar Ag08 (2-3mm Film, with Plasticizer)
      • Agar Ag09 (1.5mm Film, with Plasticizer)
      • Agar Ag10 (5mm Leather, with Plasticizer)
      • Agar Ag11 (1.5mm Film, with Plasticizer)
      • Agar Ag12 (4.5mm Film, with Plasticizer)
      • Agar Ag13 (Solid, without Plasticizer)
      • Agar Ag18 (Solid, without Plasticizer)
      • Agar Ag14 (2mm Film, without Plasticizer)
      • Agar Ag15 (3mm Film, with Plasticizer)
      • Agar Ag16 (Coating, without Plasticizer)
      • Agar Ag17 (?mm Film, with Plasticizer)
      • Agar Ag18 (4.5mm Film, with Plasticizer)
      • Agar Ag19 (Thin Film, with Plasticizer)
    • Recipes (Raw Seaweed)
      • CC01 Chrondus Crispus (Carrageenan)
      • LS01 Laminaria Saccharina (Fucodian or Alginic Acid)
      • CC02 Chrondus Crispus (Carrageenan)
      • CC03 Chrondus Crispus (Carrageenan)
      • CC04 Chrondus Crispus (Carrageenan)
      • CC05 Chrondus Crispus (Carrageenan)
      • CC06 Chrondus Crispus (Carrageenan)
    • Experiments with Bioplastic
      • Plasticizer vs. No Plasticizer
      • Freezing Bioplastic
      • Melting Bioplastic
      • Extruding Bioplastic
      • Flipped vs. Not Flipped
      • Microwaving Bioplastic
      • Burning Bioplastic
      • Heat Joining Bioplastic
      • Cooking Bioplastic
      • Water Permeability
      • Hot vs. Room Temp Drying
      • Fully Dissolving Bioplastic
      • Bioplastic in a Dehydrator
      • 3D Printing Bioplastic
      • Biodegradability
    • Science Behind Bioplastic
    • More Recipes
    • Potential Uses
  • Carbon Capture
    • Before You Start...
    • Materials
    • Test Chambers
      • Test Chamber MK1
      • Test Chamber MK2
      • Test Chamber MK3
    • Sorbent Prep
      • Sorbent #1 Prep
      • Sorbent #2 Prep
    • Tests
      • Test #1 with Sorbent #1
      • Test #2 with Sorbent #1
      • Test #3 with Sorbent #1
      • Test #4 with Sorbent #1
      • Test #5 with Sorbent #1
      • Test #6 with Sorbent #1
      • Test #7 with Sorbent #1
      • Test #8 with Sorbent #2
    • Data Analysis/Quantification
    • How Does Carbon Capture Work?
    • Further Learning
    • Was This Project a Success?
Powered by GitBook
On this page

Was this helpful?

  1. Bioplastic
  2. Recipes (Refined Seaweed)

Agar Ag12 (4.5mm Film, with Plasticizer)

PreviousAgar Ag11 (1.5mm Film, with Plasticizer)NextAgar Ag13 (Solid, without Plasticizer)

Last updated 1 year ago

Was this helpful?

Ingredients:

  • Water (75 mL)

  • Agar agar powder (3 g)

  • Glycerol (4.4 g)

Procedure:

  • Mix all the ingredients into a pan or pot

  • Heat up all the ingredients to 85-90 C on the stove

  • Mix thoroughly

  • Lower heat if bubbles are forming on the bottom of the pan

  • Take off heat after about 4 minutes of stirring or until the agar is fully dissolved (the solution is at least 85 C and thicker than when started)

  • Let dry for a few days on silicone or something similar. I used an 11.5 X 16.5 cm silicone mat. When poured onto my mat, it naturally reached all four corners and was about 4.5mm thick.

  • Done!

Properties:

  • Before drying: very viscous and brown

  • After drying: a thicker film that's super strong!

Notes:

  • Final thickness: 0.5mm (it shrunk about 9 times in thickness!)

  • Varied casting thickness

  • It's really hard to measure the casting thickness, so I'm going to note it could have been between 3.5-5mm.

  • Super strong

  • Translucent

  • Flexible

  • Best film yet!

  • Oh my goodness this takes forever to dry!