🌎
Nicholson Labs
  • About
  • Bioplastic
    • Tools and Materials
    • Tips and Tricks
    • Recipes (Refined Seaweed)
      • Carrageenan Ca01 (Solid, without Plasticizer)
      • Agar Ag01 (Solid, with Plasticizer)
      • Agar Ag02 (Film, with Plasticizer)
      • Agar Ag03 (Solid, with Plasticizer)
      • Agar Ag04 (Film, with Plasticizer)
      • Agar Ag05 (Solid, with Plasticizer)
      • Agar Ag06 (Solid, with Plasticizer)
      • Agar Ag07 (Foam, with Plasticizer)
      • Agar Ag08 (2-3mm Film, with Plasticizer)
      • Agar Ag09 (1.5mm Film, with Plasticizer)
      • Agar Ag10 (5mm Leather, with Plasticizer)
      • Agar Ag11 (1.5mm Film, with Plasticizer)
      • Agar Ag12 (4.5mm Film, with Plasticizer)
      • Agar Ag13 (Solid, without Plasticizer)
      • Agar Ag18 (Solid, without Plasticizer)
      • Agar Ag14 (2mm Film, without Plasticizer)
      • Agar Ag15 (3mm Film, with Plasticizer)
      • Agar Ag16 (Coating, without Plasticizer)
      • Agar Ag17 (?mm Film, with Plasticizer)
      • Agar Ag18 (4.5mm Film, with Plasticizer)
      • Agar Ag19 (Thin Film, with Plasticizer)
    • Recipes (Raw Seaweed)
      • CC01 Chrondus Crispus (Carrageenan)
      • LS01 Laminaria Saccharina (Fucodian or Alginic Acid)
      • CC02 Chrondus Crispus (Carrageenan)
      • CC03 Chrondus Crispus (Carrageenan)
      • CC04 Chrondus Crispus (Carrageenan)
      • CC05 Chrondus Crispus (Carrageenan)
      • CC06 Chrondus Crispus (Carrageenan)
    • Experiments with Bioplastic
      • Plasticizer vs. No Plasticizer
      • Freezing Bioplastic
      • Melting Bioplastic
      • Extruding Bioplastic
      • Flipped vs. Not Flipped
      • Microwaving Bioplastic
      • Burning Bioplastic
      • Heat Joining Bioplastic
      • Cooking Bioplastic
      • Water Permeability
      • Hot vs. Room Temp Drying
      • Fully Dissolving Bioplastic
      • Bioplastic in a Dehydrator
      • 3D Printing Bioplastic
      • Biodegradability
    • Science Behind Bioplastic
    • More Recipes
    • Potential Uses
  • Carbon Capture
    • Before You Start...
    • Materials
    • Test Chambers
      • Test Chamber MK1
      • Test Chamber MK2
      • Test Chamber MK3
    • Sorbent Prep
      • Sorbent #1 Prep
      • Sorbent #2 Prep
    • Tests
      • Test #1 with Sorbent #1
      • Test #2 with Sorbent #1
      • Test #3 with Sorbent #1
      • Test #4 with Sorbent #1
      • Test #5 with Sorbent #1
      • Test #6 with Sorbent #1
      • Test #7 with Sorbent #1
      • Test #8 with Sorbent #2
    • Data Analysis/Quantification
    • How Does Carbon Capture Work?
    • Further Learning
    • Was This Project a Success?
Powered by GitBook
On this page

Was this helpful?

  1. Bioplastic

Tips and Tricks

  • When the bioplastic is wet and sticky and has no strength, you need to add more agar.

  • Don't move the bioplastic from its casting spot until it's completely dried, as it will be more transparent this way.

  • Plasticizer is pretty much a must!

  • Mold might grow on your bioplastic. A way to combat this is to make thinner castings, as these will dry faster. You might also have luck with a dehydrator, though I haven't tried. You may also have success killing the mold by freezing it, too.

PreviousTools and MaterialsNextRecipes (Refined Seaweed)

Last updated 11 months ago

Was this helpful?