🌎
Nicholson Labs
  • About
  • Bioplastic
    • Tools and Materials
    • Tips and Tricks
    • Recipes (Refined Seaweed)
      • Carrageenan Ca01 (Solid, without Plasticizer)
      • Agar Ag01 (Solid, with Plasticizer)
      • Agar Ag02 (Film, with Plasticizer)
      • Agar Ag03 (Solid, with Plasticizer)
      • Agar Ag04 (Film, with Plasticizer)
      • Agar Ag05 (Solid, with Plasticizer)
      • Agar Ag06 (Solid, with Plasticizer)
      • Agar Ag07 (Foam, with Plasticizer)
      • Agar Ag08 (2-3mm Film, with Plasticizer)
      • Agar Ag09 (1.5mm Film, with Plasticizer)
      • Agar Ag10 (5mm Leather, with Plasticizer)
      • Agar Ag11 (1.5mm Film, with Plasticizer)
      • Agar Ag12 (4.5mm Film, with Plasticizer)
      • Agar Ag13 (Solid, without Plasticizer)
      • Agar Ag18 (Solid, without Plasticizer)
      • Agar Ag14 (2mm Film, without Plasticizer)
      • Agar Ag15 (3mm Film, with Plasticizer)
      • Agar Ag16 (Coating, without Plasticizer)
      • Agar Ag17 (?mm Film, with Plasticizer)
      • Agar Ag18 (4.5mm Film, with Plasticizer)
      • Agar Ag19 (Thin Film, with Plasticizer)
    • Recipes (Raw Seaweed)
      • CC01 Chrondus Crispus (Carrageenan)
      • LS01 Laminaria Saccharina (Fucodian or Alginic Acid)
      • CC02 Chrondus Crispus (Carrageenan)
      • CC03 Chrondus Crispus (Carrageenan)
      • CC04 Chrondus Crispus (Carrageenan)
      • CC05 Chrondus Crispus (Carrageenan)
      • CC06 Chrondus Crispus (Carrageenan)
    • Experiments with Bioplastic
      • Plasticizer vs. No Plasticizer
      • Freezing Bioplastic
      • Melting Bioplastic
      • Extruding Bioplastic
      • Flipped vs. Not Flipped
      • Microwaving Bioplastic
      • Burning Bioplastic
      • Heat Joining Bioplastic
      • Cooking Bioplastic
      • Water Permeability
      • Hot vs. Room Temp Drying
      • Fully Dissolving Bioplastic
      • Bioplastic in a Dehydrator
      • 3D Printing Bioplastic
      • Biodegradability
    • Science Behind Bioplastic
    • More Recipes
    • Potential Uses
  • Carbon Capture
    • Before You Start...
    • Materials
    • Test Chambers
      • Test Chamber MK1
      • Test Chamber MK2
      • Test Chamber MK3
    • Sorbent Prep
      • Sorbent #1 Prep
      • Sorbent #2 Prep
    • Tests
      • Test #1 with Sorbent #1
      • Test #2 with Sorbent #1
      • Test #3 with Sorbent #1
      • Test #4 with Sorbent #1
      • Test #5 with Sorbent #1
      • Test #6 with Sorbent #1
      • Test #7 with Sorbent #1
      • Test #8 with Sorbent #2
    • Data Analysis/Quantification
    • How Does Carbon Capture Work?
    • Further Learning
    • Was This Project a Success?
Powered by GitBook
On this page

Was this helpful?

  1. Bioplastic
  2. Recipes (Refined Seaweed)

Agar Ag18 (4.5mm Film, with Plasticizer)

PreviousAgar Ag17 (?mm Film, with Plasticizer)NextAgar Ag19 (Thin Film, with Plasticizer)

Last updated 1 year ago

Was this helpful?

Ingredients:

  • Water (75 mL).

  • Agar agar powder (3 g).

  • Glycerol (4 g).

Procedure:

  • Add all ingredients into a 500 mL autoclave bottle and shake thoroughly with lid closed.

  • Loosely open lid.

  • Microwave for 20 seconds on high with the goal of boiling the agar solution.

  • Take out of microwave and close lid.

  • Shake for one minute to dissolve.

  • Repeat last 4 steps 4 more times.

  • Once repeated 4 more times, cast into a mold (I used a 11.5 X 16.5 cm silicone mat).

Properties:

  • Before drying: bubbles on the surface and sort of looks liked diluted pee.

  • After drying: strong, smooth, and a less concerning color.

Notes:

  • Keep a good eye on the bioplastic while microwaving because it will boil over. When it boils over, stop the microwave and wait for a few seconds for it to calm down before continuing the microwaving.

  • A 125 mL bottle will boil over almost immediately. Trust me!

  • Because of the bubbles produced in the microwaving process, there were bubbles in my bioplastic. Besides that, the bioplastic is very smooth and has no imperfections.

  • This is the absolute best bioplastic yet by a land slide! Super smooth and consistent. It looks and feels like vinyl. Furthermore, it is very close to being fully transparent. I can't wait to modify this recipe!

More photos: